Ultimate UNO R3 Starter Kit for Arduino Beginners ( Item#: E2428 )

Fitting of DIY, great for Arduino DIY project, exercise your hand and brain. You can learn skills for Arduino from 0 with our PDF guide book (given by a download link after you receive the kit) include codes, code explanation, hardware analysis, schematics for all modules and fritzing illustration wiring.

Features:
OLED display temperature and humidity with DHT11 sensor.
Smart phone control DC motor via HC-06 Bluetooth module for Android.
Reed switch control DC Motor, great for arduino diy.
PIR motion sensor with buzzer alarm security.
Password lock, press the right password and servo turns.
LCD1602 coming with soldered on IIC module takes only 4 I/O for Arduino.
High quality proto type shield has IC pattern for adding DIP IC up to 20 pins.
UNO R3 board will be tested before shipment.

NOTE:
This UNO is manufactured using the knowledge sharing files provided on the website for Arduino, therefore it is not manufactured by factory for Arduino but is fully compatible for Arduino software(IDE) in every way and COST MUCH LESS!
Add A6 and A7 analog I/O.
Add two rows of the pass-thru holes for connecting normal dupont line.
Come with SHIELD 50CM LONG USB cable for stable data transit.

Specifications:
Color: Multicolor
Material: PCB Board 
Battery for Controller: 1 * CR2025 3V 160mAH (Included)
Battery for Clock Module: 1 * CR2032 3V 210mAH (Included)
Package Size: 25 * 16.5 * 6cm / 9.84 * 6.50 * 2.36in 
Package Weight: 698g / 24.61oz

Package List:
1 * SMD Version UNO R3 Mainboard
1 * USB Cable
1 * Prototype Board with Mini Breadboard
1 * 830 Contact Points Transparent Breadboard
1 * 0.96inch OLED SPI Display
1 * 5mm LED Assorted Kit (Red/Green/Yellow 10pcs each + White 5pcs + RGB Trip-color 1Piece)
1 * 8bit Shift Register 74hc595
1 * MAX7219 Chip
1 * Eight-segment Display (1-digit Common Anode)
1 * Eight-segment Display (4-digit Common Anode) with Clock
1 * Resistors Kit(20pcs 220Ω, 1pc 330Ω, 5pcs 1kΩ, 1pc 2k2Ω,5pcs 10kΩ)
1 * 0.1uF Ceramic Capacitor
1 * 10uF Eletrolysis Capacitor
1 * 2N2222 Transistors
1 * 1N4001 Diodes
1 * 1N4007 Diodes
1 * Light Dependent Resistor (Photocell)
1 * LM35 Temperature Sensor
1 * Mercury Switch
1 * Flame Sensor
1 * Infrared Sender
1 * Infrared Receiver
1 * Reed Switch
1 * 4mm Magnet
2 * 130 DC Motor
1 * Motor Fan
1 * IRF520
1 * 1602 LCD Display with IIC Module( No need soldering, takes ONLY 4 I/O)
1 * PS2 Joystick Module
1 * Stepping Motor 5V
1 * Stepping Motor Driver Board
1 * 9g Servo
1 * SMD5050 RGB Module
1 * 2.54mm Straight 40 Pin Header
1 * Remote Controler (Battery- CR2025 Not Included)
1 * 8*8 Dot Matrix Display
1 * 5V 10A Relay Module with Optocouple
1 * Timer IC NE555
1 * Optocoupler 4N35
1 * HC-06 Bluetooth Module1
1 * DHT11 Tempreture and Humidity Sensor
1 * PIR Motion Sensor
1 * DS1307 RTC Clock
1 * 16 Keys Membrane Keypad
1 * Sound Sensor Module
1 * DC 9V Battery Case
2 * 10k Trimpot Adjustable Resistor Potentiometer
2 * Buzzer 5V (1 active and 1 passive)
5 * Colorful Push Button Switch 12*12mm
5 * Mini Push Button Switches 6*6mm
65 * Jumper Wires
40 * Female to Male Dupont Wire
1 * Storage Box