Favorites
  • Ultimate UNO R3 Starter Kit for Arduino
Ultimate UNO R3 Starter Kit for Arduino

Ultimate UNO R3 Starter Kit for Arduino

Servo Motor Relay RTC LED with Stepper Motor LCD1602 PIR RTC DHT11 Sensors Servo Breadboard Jumper Wire

Ship From:

  • China Warehouse

Dispatch:Usually will be shipped inbusiness dayshours

Shipping: Loading...
Sorry, it seems that there are no available shipping methods for your location.Please contact us for further assistance.

Loading...

Ship to

Anguilla
: china

QTY:

Wholesale Inquiry

Special discount has ended

Please note each user for only 1 item(s)

Buyer Protection

  • Full Refund If you don't receive your order
  • Full or Partial Refund , If the item is not as described Learn more >
Fitting of DIY, great for Arduino DIY project, exercise your hand and brain. This starter kit is designed for the new starters for Arduino. You can learn skills for Arduino from 0 with our PDF guide book (given by a download link) include codes, code explanation, hardware analysis, schematics for all modules and fritzing illustration wiring.

Features:
Completely compatible for Arduino Uno R3(with Atmega16U2 as the high speed USB chip, not some kind of cheap USB converters that is easy to be broken).
3.3V/5V selectable working voltage, there are many 3.3V and 5V modules for Arduino world. With the Uno R3, you can use your 3.3V and 5V modules easily, no need to use Logical Level Converter, simple for circuit and practice.
Good current performance(1000mA current for 3.3V and 5V output).
"Reset" LED added. When you reset the board, the "Reset" LED will show if the "reset" action has been done successfully.
Short-circuit protection. Even if your circuit is short-circuited, the board will protect itself. Most cheap boards don't have such function, if they are short-circuited carelessly, then it will smoke.
Including new extension board for Arduino and the GPIO extension board. These two boards plus the bread board can work together and make it easier for you to make your project.
New sound sensor module having Analog and Digital output. You can get an analog environment noisy level, in addition you can also set the threshold for the digital output. When the noise exceed a designed level, the digital output will output a HIGH voltage.

NOTE:
This UNO is manufactured using the knowledge sharing files provided on the website for Arduino, therefore it is not manufactured by factory for Arduino but is fully compatible for Arduino software(IDE) in every way and COST MUCH LESS!
Come with a bulk of components, electronic modules that are common-used during learning for Arduino.
All the schematics of the electronic modules are included in the PDF file.
PDF file of learning lessons, with circuits, code, explanation, etc. 
Technical support with professional guide.

Specifications:
Color: Multicolor
Material: PCB Board 
Battery for Controller: 1 * CR2025 3V 160mAH (Included)
Battery for RTC Module: 1 * CR2032 3V 210mAH (Included)
Package Size: 25 * 16.5 * 6cm / 9.84 * 6.50 * 2.36in 
Package Weight: 661g / 23.33oz

Package List:
1 * Uno R3 Mainboard 
1 * USB Cable(0.5m Length)
1 * Extension Board
1 * GPIO Extension Board 
1 * Connecting Cable
1 * Big Breadboard(830 points)
1 * Mini Breadboard
10 * 3mm Red LEDs
10 * 3mm Green LEDs
10 * 3mm Yellow LEDs
1 * 5mm RGB LED
5 * Button with Cap
20 * 330 ohm Color Ring Resistor
20 * 1k ohm Color Ring Resistor
20 * 10k ohm Color Ring Resistor
1 * 1K Adjustable Trim Pot Resistor(Potentiometer)
1 * 10K Adjustable Trim Pot Resistor(Potentiometer)
1 * 2.54mm Elbow 40 Pin Header
1 * 2.54mm Straight 40 Pin Header
1 * 5516 Light Dependent Resistor(Photoresistor)
1 * Ball Switch
1 * Active Buzzer 5V
1 * Passive Buzzer 5V
1 * MAX7219 Chip 
1 * 74HC595 8bit Shift Register
1 * LM35 Temperature Sensor
1 * SS8050 NPN Transistor
1 * Infrared Receiver(Type 1838)
1 * Infrared Sender
1 * Infrared Phototransistor(Flame Sensor)
1 * Infrared Remote Controller 
1 * Stepper Motor(5V)
1 * SG90 Servo Motor
1 * 1602 LCD
1 * 1-Digit Eight-segment Display
1 * 4-Digit Eight-segment Display
1 * 8*8 Dot Matrix Led Display
1 * Stepper Motor Driver Board
1 * Sound Sensor Module(With "Digital" and "Analog" output)
1 * PS2 Joystick module
1 * RTC Module 
1 * Relay Module(5V-10A)
65 * Jump Wires
10 * Female-Female Dupont Wires
10 * Male-Female Dupont Wires
1 * 9V Battery Holder(9V Battery is not included)
1 * Storage Box
Customer Reviews

There are no customer reviews yet.

  • 5 stars
  • 4 stars
  • 3 stars
  • 2 stars
  • 1 stars

Share your thoughts with other customers and get Cafago Points, the first 5 reviews get DOUBLE Cafago Points!

Write a Customer Review
Be the first to review this item

Top Sellers More

Please activate your account and then to buy,We will resend the activation email to help you complete your registration.

cafago use cookies to give you the best shopping experience. If you continue to use our services or create a new account, we will assume that you agree to our  Privacy Policy.
Click here to reject the cookies